收藏本站

ADM1175
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Data Sheet
VCC 1
10 GATE
SENSE 2
ON/ONB 3
GND 4
TIMER 5
ADM1175
TOP VIEW
(Not to Scale)
9
8
7
6
CONV
ADR
SDA
SCL
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
Mnemonic
VCC
SENSE
ON/ONB
GND
TIMER
SCL
SDA
ADR
CONV
GATE
Description
Positive Supply Input Pin. The operating supply voltage range is from 3.15 V to 16.5 V. An undervoltage
lockout (UVLO) circuit resets the ADM1175 when a low supply voltage is detected.
Current Sense Input Pin. A sense resistor between the VCC pin and the SENSE pin sets the analog current
limit. The hot swap operation of the ADM1175 controls the external FET gate to maintain the (V CC ? V SENSE )
voltage at or below 100 mV.
Undervoltage or Overvoltage Input Pin. This pin is active high on the ADM1175-1 and ADM1175-2 and
active low on the ADM1175-3 and ADM1175-4. An internal undervoltage comparator has a trip threshold of
1.3 V, and the output of this comparator is used as an enable for the hot swap operation. For the ON pin
variants with an external resistor divider from VCC to GND, this pin can be used to enable the hot swap
operation for a specific voltage on VCC, providing an undervoltage function. Similarly, for the ONB pin
variants, an external resistor divider can be used to create an overvoltage function, where the divider sets a
voltage on VCC, at which the hot swap operation is switched off, pulling the GATE to ground.
Chip Ground Pin.
Timer Pin. An external capacitor, C TIMER , sets a 270 ms/μF initial timing cycle delay and a 21.7 ms/μF fault delay.
The GATE pin turns off when the TIMER pin is pulled beyond the upper threshold. An overvoltage detection
with an external Zener can be used to force this pin high.
I 2 C Clock Pin. Open-drain input requires an external resistive pull-up.
I 2 C Data I/O Pin. Open-drain input/output. Requires an external resistive pull-up.
I 2 C Address Pin. This pin can be tied low, tied high, left floating, or tied low through a resistor to set four
different I 2 C addresses.
Convert Start Pin. A high level on this pin enables an ADC conversion. The state of an internal control register,
which is set through the I 2 C interface, configures the part to convert current only, voltage only, or both
channels when the convert pin is asserted. This pin must be pulled high to allow conversions to take place.
GATE Output Pin. This pin is the high-side gate drive of an external N-channel FET. This pin is driven by the
FET drive controller, which utilizes a charge pump to provide a 12.5 μA pull-up current to charge the FET
GATE pin. The FET drive controller regulates to a maximum load current (100 mV through the sense resistor)
by modulating the GATE pin.
Rev. C | Page 6 of 24
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADM1176EBZ BOARD EVALUATION FOR ADM1176
EVAL-ADM1177EBZ BOARD EVALUATION FOR ADM1177
EVAL-ADM1178EBZ BOARD EVALUATION FOR ADM1178
EVAL-ADM1191EBZ BOARD EVALUATION FOR ADM1191
EVAL-ADM1192EBZ BOARD EVALUATION FOR ADM1192
EVAL-ADM1275EBZ BOARD EVALUATION FOR ADM1275
EVAL-ADM1276EBZ BOARD EVAL FOR ADM1276
EVAL-ADM2483EBZ BOARD EVAL FOR ADM2483
相关代理商/技术参数
EVAL-ADM1176EBZ 功能描述:BOARD EVALUATION FOR ADM1176 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1177EBZ 功能描述:BOARD EVALUATION FOR ADM1177 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1178EBZ 功能描述:BOARD EVALUATION FOR ADM1178 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1178MEBZ 功能描述:BOARD EVALUATION FOR ADM1178 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1184 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Kit for ADM1184 ?±0.8% Accurate Quad Voltage Monitor
EVAL-ADM1184EBZ 功能描述:BOARD EVAL FOR ADM1184 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1185EBZ 功能描述:BOARD EVALUATION FOR ADM1185 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADM1186-1EBZ 功能描述:KIT EVALUATION FOR ADM1186-1 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081